We're Proud of the Work that Erik Does in Warren

I was hired to replace a gas valve and perform maintenance on a furnace. The gas valve was leaking, so I replaced it with a new one and made sure the furnace was working properly. I also checked the air filter and cleaned it if necessary.

I was called to a home to replace a gas valve and perform a tune-up on the furnace. When I arrived, I found that the gas valve was leaking and needed to be replaced. I also noticed that the furnace was not producing heat as efficiently as it should be. I performed a tune-up on the furnace, including cleaning the burners, checking the ignition system, and adjusting the thermostat. After completing the tune-up, the furnace was producing heat more efficiently and the homeowner was happy with the results.

I was called to a home in the middle of a hot summer to find that the air conditioner was not working. Upon arrival, I found that the thermostat was not working properly. I replaced the thermostat and tested it to ensure it was working properly. I also checked the air filter and found that it was dirty, so I cleaned it and replaced it. After completing the repairs, the customer was happy with the results and thanked me for my help.

I am a highly skilled and experienced home service professional. I recently completed a job that involved mounting radiators to the wall. The radiators were heavy and required careful installation to ensure they were secure and stable. I started by measuring the wall and marking the locations for the radiators. I then cut the radiators to the correct size and secured them in place with brackets and screws. I also made sure that the radiators were level and plumb before attaching them to the wall. Finally, I cleaned up the work area and made sure that the radiators were operating properly. The client was very pleased with the results and I was proud of my work.

I was hired to perform maintenance on a water boiler at a large office building. The boiler was used to heat water for the building's heating system. I started by inspecting the boiler to identify any potential issues. I then replaced the anode rod, which is a metal rod that protects the boiler from corrosion. I also cleaned the boiler's heat exchanger and inspected the burner for any signs of wear. Finally, I tested the boiler's pressure relief valve and adjusted it as needed. After completing the maintenance, I tested the boiler again to ensure it was operating properly.

I was tasked with performing a tune-up on a steam boiler at a large industrial facility. The boiler had been experiencing issues with efficiency and had been running at a lower capacity than expected. To begin the tune-up, I inspected the boiler for any visible signs of damage or wear. I then cleaned the boiler's interior and exterior surfaces, removing any debris or buildup that could be affecting its performance. Next, I checked the boiler's pressure and temperature gauges to ensure they were functioning correctly. If any issues were detected, I adjusted the settings accordingly. I also performed a thorough inspection of the boiler's combustion chamber and combustion system. I checked for any signs of corrosion or damage and cleaned or replaced any components that were found to be faulty. Finally, I performed a leak test on the boiler to ensure that there were no leaks that could be causing the efficiency issues. If any leaks were detected, I repaired them immediately. After com

I was called to a commercial building to perform maintenance on a boiler and air handler. Upon arrival, I found that the boiler was not producing enough heat for the building. I inspected the boiler and found that the burner was not igniting. I replaced the burner and the boiler started producing heat again. I also noticed that the air handler was not blowing air properly. I inspected the air handler and found that the fan motor was not working. I replaced the fan motor and the air handler started blowing air properly again. I also checked the refrigerant levels in the air handler and found that they were low. I added more refrigerant and the air handler started blowing cold air again. I also checked the electrical connections in the air handler and found that they were loose. I tightened the electrical connections and the air handler started working properly again. I also checked the thermostat and found that it was not working properly. I replaced the thermostat and the air handler s

I was called to inspect a spacepak unit that was not cooling properly. Upon arrival, I found that the unit was not producing any cool air. I checked the refrigerant levels and found that they were low. I added more refrigerant and recharged the system. After the recharge, the unit was cooling properly. I tested the system for leaks and found no issues. The customer was happy with the results and thanked me for my help.

I was called to a client's house to perform maintenance on their generator. The generator had been making strange noises and wasn't working properly. After inspecting the generator, I found that the fuel line had been damaged. I replaced the fuel line and tested the generator to ensure it was working properly. The client was very happy with the service and thanked me for my help.

I am a highly skilled HVAC contractor professional. I recently completed a job where I performed maintenance on a tankless water heater. The tankless water heater was installed in a residential home and was not producing hot water. I diagnosed the issue as a faulty thermocouple, which was causing the water heater to not heat the water. I replaced the thermocouple and tested the water heater to ensure it was working properly. The homeowner was very pleased with the results and thanked me for my expertise.

I was tasked with performing a tune-up on a water boiler at a residential property. The boiler was not producing enough hot water, and I diagnosed the issue as a faulty thermostat. I replaced the thermostat and tested the boiler to ensure it was functioning properly. I also cleaned the boiler and flushed the water lines to remove any debris or sediment that may have been causing the issue.

I performed a thorough inspection on a furnace to identify any potential issues. I checked the electrical connections, inspected the burner assembly, and tested the gas pressure. I also cleaned the burners and inspected the heat exchanger for any signs of corrosion or damage. After the inspection, I provided a detailed report to the customer, including recommendations for any necessary repairs or maintenance.

I was hired to inspect two boilers at a commercial building. The boilers were located in the basement and were used to heat the building. I used a variety of tools to inspect the boilers, including a pressure gauge, a thermometer, and a borescope. I checked the pressure of the boilers, the temperature of the water, and the condition of the burners and valves. I also checked the insulation and the piping to ensure that they were in good condition. After the inspection, I provided a report to the building owner outlining my findings and recommending any necessary repairs.

I was called to a home to inspect a leaking water heater. Upon arrival, I found that the water heater was leaking from the bottom. I inspected the unit and found that the tank was rusted and corroded, which was causing the leak. I replaced the rusted tank with a new one and made the necessary repairs to prevent further leaks. The homeowner was very pleased with the work and thanked me for my expertise.

I am a highly skilled and experienced home service professional who specializes in boiler tune-ups. I have been in the industry for over 10 years and have worked on countless boilers of all sizes and types. One of the most important aspects of a boiler tune-up is to ensure that the boiler is operating at peak efficiency. This involves cleaning the boiler, checking the pressure, and adjusting the burners and valves. I also check the safety controls and make any necessary repairs or replacements. During a boiler tune-up, I also take the opportunity to inspect the boiler's other components, such as the heat exchanger, pump, and controls. I look for any signs of wear or damage and make any necessary repairs or replacements. I also provide my customers with a detailed report of the tune-up, including any recommendations for future maintenance. I believe that providing my customers with this information is essential to ensuring that their boilers are operating safely and efficiently. In

I was called to a home to perform a tune-up on a furnace. The furnace was not heating the home properly, and the customer was concerned that it might need to be replaced. I arrived at the home and performed a thorough inspection of the furnace. I checked the burners, the blower, and the thermostat. I also checked the air filter and the vent system. After completing the inspection, I performed the necessary repairs to the furnace. I replaced the burners, the blower, and the thermostat. I also cleaned the air filter and the vent system. The furnace was now heating the home properly, and the customer was happy with the results.

I was hired to perform a tune-up on a furnace. The furnace was not producing heat properly, so I diagnosed the issue and replaced the faulty parts. I also cleaned the furnace and checked the safety features to ensure it was working properly.

I am a highly skilled and experienced home service professional. I recently completed an inspection on a furnace. The inspection was thorough and included checking the furnace's components, such as the blower, heat exchanger, and combustion chamber. I also tested the furnace's airflow and gas pressure to ensure it was operating correctly. If any issues were found, I provided a detailed report with recommendations for repair or replacement.

I was hired to perform maintenance on a water boiler at a large office building. The boiler was used to heat water for the building's heating system. The first step was to drain the boiler and remove any sediment or debris that had accumulated inside. Then, I cleaned the boiler's interior with a brush and a cleaning solution. Next, I replaced the boiler's gaskets and seals. Finally, I tested the boiler to ensure it was working properly.

I was called to replace an inducer motor on a furnace. The motor had failed and was causing the furnace to not heat the house. I removed the old motor and replaced it with a new one. I also checked the wiring and connections to ensure they were all secure. After completing the repair, I tested the furnace to ensure it was working properly. The customer was happy with the work and thanked me for my help.

I was called to a home to relight a pilot on a furnace. When I arrived, I found that the pilot light had gone out. I checked the gas line and found that it was not blocked. I then checked the thermostat and found that it was working properly. I then relit the pilot light and tested the furnace to ensure that it was working properly. I then cleaned up the area and left the home.

I was called to a home to perform a tune-up on a water boiler. The boiler had been running poorly and was not heating the water as it should. I inspected the boiler and found that the burner was not igniting properly. I replaced the burner and tested the boiler again. The boiler was now heating the water to the correct temperature. The customer was very happy with the service and thanked me for my help.

I was hired to perform skimming on a boiler. I used a variety of tools to remove the old finish and prepare the surface for a new coat of paint. I also repaired any damage to the boiler and replaced any broken parts.

I am a highly skilled HVAC contractor professional. I recently completed a job where I had to unclog a condensate drain on a mini split. The condensate drain is a small pipe that carries condensation from the air conditioner to the outside. Over time, the drain can become clogged with dirt, debris, or even algae. To unclog the drain, I started by turning off the power to the mini split. Then, I removed the access panel on the outside of the unit. Inside, I could see the condensate drain pipe. It was clogged with a lot of debris, including leaves, twigs, and even a small bird's nest. I used a plumbing snake to gently push the debris out of the pipe. It was a slow process, but eventually, the pipe was clear. I then replaced the access panel and turned the power back on. After completing the job, I tested the mini split to make sure the condensate drain was working properly. The air conditioner was running smoothly, and there was no more clogging. Unclogging a condensate drain on a min

I was called to a home to inspect a thermostat that was not turning the heat on. Upon arrival, I found that the thermostat was not connected to the furnace. I checked the wiring and found that the wires were not connected properly. I reconnected the wires and tested the thermostat. The heat was now working properly.